Selection guides

CM5 vs CM4 for industrial use

Updated

For a new industrial design, the Compute Module 5 is usually the better choice: it has a much faster CPU, two USB 3.0 ports, up to 16 GB of RAM, and Raspberry Pi commits to producing it until at least January 2036, two years longer than the CM4. The CM4 still makes sense when cost per unit matters most, when you need its -40 °C extended-temperature variant, or when you are buying more of a CM4 controller that is already installed.

The specifications side by side

Figures are from Raspberry Pi’s product pages, as of 2026-11-19.

Compute Module 4 Compute Module 5
SoC Broadcom BCM2711 Broadcom BCM2712
CPU 4× Cortex-A72 at 1.5 GHz 4× Cortex-A76 at 2.4 GHz
RAM 1, 2, 4 or 8 GB LPDDR4-3200 2, 4, 8 or 16 GB LPDDR4-4267
eMMC None (Lite), 8, 16 or 32 GB None (Lite), 16, 32 or 64 GB
USB Not stated on product page 1× USB 2.0, 2× USB 3.0
PCIe Not stated on product page 1× PCIe Gen 2 x1
Ethernet Not stated on product page Gigabit PHY with IEEE 1588
Operating temperature -20 to +85 °C; -40 to +85 °C on extended-temperature variants -20 to +85 °C
In production until at least January 2034 January 2036
Price from $41.25 $67.50

Sources: CM4 product page, CM5 product page, CM5 product brief.

The CM5 launched on 27 November 2024 “priced from just $45” (Raspberry Pi News). The product page now shows $67.50, so check current prices before costing a design.

Is the CM5 a drop-in replacement for the CM4?

Mostly, not entirely. Raspberry Pi says the CM5 is “mechanically compatible” with the CM4, with “a small number of changes to the pin-out and electrical behaviour”, mostly from removing the two two-lane MIPI interfaces and adding two USB 3.0 interfaces (Raspberry Pi News). In practice:

  • A CM4 carrier board may boot a CM5, but test it. Check that the board’s power supply holds up with the CM5 at full load, and check any feature that uses the changed pins.
  • Software images differ. Plan to requalify your OS image, drivers and application on the CM5, not just swap modules.
  • An industrial controller sold “for CM4” is not certified with a CM5 inside unless its vendor says so. Certifications apply to the tested configuration.

What the CM5 changes for industrial work

  • Headroom. The jump from Cortex-A72 at 1.5 GHz to Cortex-A76 at 2.4 GHz leaves room for local databases, containers, dashboards and analytics on the same unit that handles I/O.
  • Storage and I/O bandwidth. USB 3.0 and PCIe Gen 2 allow fast SSDs and add-on cards. Several CM5 controllers have M.2 slots; Strato Pi Max supports M.2 PCIe SSDs (CNX).
  • Memory. Up to 16 GB, against 8 GB on the CM4.
  • Time sync. The Gigabit PHY supports IEEE 1588 Precision Time Protocol (CM5 product page).
  • Lifecycle. Two more years of guaranteed supply, to at least January 2036.

What the CM4 still does better

  • Cold rating. The CM4 has extended-temperature variants rated to -40 °C (CM4 product page). The CM5 is rated to -20 °C. A controller’s own range is usually narrower than either module’s, so compare finished units: Seeed’s CM4-based R1100 is rated -30 to +70 °C (wiki), while its CM5-based R20xx is rated -20 to +65 °C (wiki).
  • Cost. $41.25 against $67.50 at the module level, as of 2026-11-19.
  • Heat under light loads. If the workload is light and the enclosure is sealed and hot, the faster CPU brings little benefit. Measure the enclosure temperature with each module under your real workload before deciding.
  • Installed base. Many controllers in the field use the CM4. Matching what is installed simplifies spares and software.

How the difference shows up in a real product

Revolution Pi sells the same Connect form on both modules, which makes a clean comparison, as of 2026-11-19 (product page):

RevPi Connect 4 RevPi Connect 5
Module CM4 CM5
CPU Cortex-A72, 1.5 GHz Cortex-A76, 2.4 GHz
RAM 2, 4 or 8 GB 4 or 8 GB
CAN FD No Up to 2
Price from (excl. tax) €418 €536

The Connect 5 costs €118 more and adds speed and CAN FD. Its documentation gives an approved operating range of -25 to +60 °C for typical use (docs).

Which should you choose?

Your situation Choose
New design, expected to be sold or supported past 2034 CM5
Local data storage, containers, dashboards or vision on the controller CM5
Site regularly below -20 °C, and a controller rated for it exists CM4 extended-temperature, or a CM5 controller with a published wider range
Lowest unit cost, light workload CM4
Adding units to an existing CM4 fleet CM4, then plan the move to CM5

halfnine is designing around the CM5. To be decided: halfnine module variant, RAM and temperature rating, once confirmed.

Sources

  1. Raspberry Pi Compute Module 5 product page, accessed 2026-11-19
  2. Raspberry Pi Compute Module 5 product brief, accessed 2026-11-19
  3. Raspberry Pi Compute Module 4 product page, accessed 2026-11-19
  4. Raspberry Pi News, Compute Module 5 on sale now (2024-11-27), accessed 2026-11-19
  5. Revolution Pi Connect product page, accessed 2026-11-19
  6. RevPi Connect 5 documentation, accessed 2026-11-19
  7. CNX Software, Strato Pi Max with Raspberry Pi CM5 (2024-12-12), accessed 2026-11-19
  8. Seeed Studio wiki, reComputer R1100, accessed 2026-11-19
  9. Seeed Studio wiki, reComputer Industrial R20xx, accessed 2026-11-19