Selection guides
Is a Raspberry Pi reliable enough for industry?
Updated
A standard Raspberry Pi board, powered from a USB adapter and booting from a microSD card, is not reliable enough for most industrial jobs. Most of its failures come from the setup around the board, not the processor: card wear, file systems corrupted by power cuts, weak power supplies and heat. A Raspberry Pi Compute Module inside a controller designed for industrial use addresses those causes, and many such controllers run in the field. How reliable your system is depends on the controller you pick and on how you build the software.
Why Raspberry Pis get a reputation for failing
The common failure stories have a few causes:
- microSD cards wear out and corrupt. Constant logging writes to cheap flash, and a power cut during a write can damage the file system.
- Undersized or noisy power. Hobby supplies sag under load or pass surges through.
- Heat. A bare board in a closed box throttles or ages faster.
- No recovery. Without a watchdog, a hung process stays hung until someone visits.
- Unmaintained software. A system nobody updates becomes a security risk.
None of these are inherent to the processor. They are design choices that an industrial controller can make differently.
What the Compute Module itself provides
The Compute Module is the industrial form of the Raspberry Pi:
- Soldered eMMC instead of microSD. The CM5 has 16, 32 or 64 GB of MLC eMMC (Raspberry Pi News).
- Rated temperature. The CM5 is rated -20 to +85 °C (CM5 brief). The CM4 has extended-temperature variants rated -40 to +85 °C (CM4 product page).
- Long supply commitment. At least January 2036 for the CM5 and January 2034 for the CM4 (CM5, CM4). That lets you buy identical spares for years.
Raspberry Pi does not give an MTBF figure on the CM5 product page or product brief. Some controller vendors publish one for the finished unit: CompuLab lists an MTTF of more than 200,000 hours for the IOT-GATE-RPI5 (CompuLab). Ask how such a figure was calculated before comparing it with another.
What an industrial controller adds
Compare these features across products. Examples are from vendor pages as of 2026-11-19.
| Feature | Why it matters | Examples |
|---|---|---|
| Wide-range 24 V input with protection | Survives cabinet supplies, dips and reverse wiring | RevPi Connect 5: 10.8–28.8 V DC (docs); CompuLab: 12–24 V with reverse-voltage protection (CompuLab) |
| Hardware watchdog | Restarts the system if software hangs | Seeed R20xx: 1–255 s (wiki) |
| Power-loss backup | Time to shut down cleanly or finish writes | Seeed R20xx: optional supercapacitor UPS (wiki) |
| Redundant storage | Survives a failed card | Strato Pi Max XL: dual microSD (CNX) |
| Isolated I/O and serial | Protects the CPU from field wiring faults | Seeed R20xx: isolated DI, DO, RS485 (wiki) |
| Fanless enclosure | No fan to fail | CompuLab, Seeed R20xx (both state fanless) |
| Industrial EMC testing | Keeps working next to drives and contactors | CompuLab: EN 61000-6-2 (CompuLab) |
| Design to PLC standard | Defined tests for I/O, power and noise (IEC 61131-2) | RevPi: “developed according to” EN 61131-2 (product page) |
| Third-party safety listing | Independent check of the design | RevPi Connect 5: UL File No. E494534 (docs); Sfera Strato Pi CM: UL 61010-1 (announcement) |
| Warranty | Signals the vendor’s confidence | CompuLab: 5 years; Seeed R20xx: 2 years (sources above) |
What you still have to get right in software
Good hardware does not save a fragile software design. The practices that matter most:
- Limit writes to flash. Log to RAM and flush in batches, or send logs off the device. Avoid swap on eMMC.
- Make the root file system read-only where you can, with writable data on a separate partition. A power cut then cannot corrupt the OS.
- Use the hardware watchdog, and have your application feed it only while it is actually working.
- Use A/B updates so a failed update rolls back to the previous image. Raspberry Pi Connect for Organisations, for example, pushes A/B boot images ($0.50 per device per month as of 2026-11-19) (Raspberry Pi); balenaOS and Mender are alternatives.
- Restart on boot. The controller should come back into a known, safe state after power returns, without anyone logging in.
- Monitor and alarm. Watch disk health, temperature and your own process, and tell a person when something is wrong.
Where a Raspberry Pi controller is not the right tool
- Safety functions such as emergency stops belong on safety-rated relays or PLCs.
- Hard real-time control with guaranteed cycle times is the PLC’s job unless you have tested a real-time Linux setup under worst-case load.
- Hazardous areas need equipment certified for them. We found no CM5 controller with such a rating among the products we reviewed.
The short answer
| Setup | Reliable enough for industrial use? |
|---|---|
| Raspberry Pi board, microSD, USB power adapter | No, except for short trials |
| Compute Module on a hobby carrier board | Only with careful power, cooling and software work |
| Compute Module in a controller built for industry, with the software practices above | Yes, for monitoring, gateways, data collection, alarms and non-safety control |
| Any of the above for safety functions | No |
halfnine is designing a CM5 controller and software suite around these practices. To be decided: halfnine watchdog, power-loss handling, storage and update design, once confirmed.
Sources
- Raspberry Pi Compute Module 5 product page, accessed 2026-11-19
- Raspberry Pi Compute Module 5 product brief, accessed 2026-11-19
- Raspberry Pi Compute Module 4 product page, accessed 2026-11-19
- Raspberry Pi News, Compute Module 5 on sale now (2024-11-27), accessed 2026-11-19
- RevPi Connect 5 documentation, accessed 2026-11-19
- Revolution Pi Connect product page, accessed 2026-11-19
- Seeed Studio wiki, reComputer Industrial R20xx, accessed 2026-11-19
- CompuLab IOT-GATE-RPI5 product page, accessed 2026-11-19
- CNX Software, Strato Pi Max with Raspberry Pi CM5 (2024-12-12), accessed 2026-11-19
- Electronica Azi, Sfera Labs announces UL listing of Strato Pi CM and CM Duo, accessed 2026-11-19
- IEC 61131-2:2017, Programmable controllers, equipment requirements and tests, accessed 2026-11-19
- Raspberry Pi Connect for Organisations, accessed 2026-11-19