Standards and compliance
UL 508A panels and the controllers inside them
Updated
Usually not, unless the panel shop takes on extra work. A UL 508A panel is built from components that are listed, recognized and used within their conditions, or evaluated by UL. An unlisted Raspberry Pi-based controller fits only in narrow cases: when every electrical connection it has is to a Class 2 or low-voltage limited-energy circuit, when the UL representative evaluates it, or when the finished panel gets a field evaluation instead of a 508A listing.
This page explains how the rules work; it is not legal or certification advice. Your UL representative and the authority having jurisdiction (AHJ) decide each case.
What is a UL 508A panel?
The US National Electrical Code, Article 409, defines an industrial control panel as an assembly of two or more power-circuit or control-circuit components, for general use at less than 600 V. UL lists these panels to UL 508A, under product category NITW (UL, Recognized Component Marks). A panel shop with a UL 508A programme applies the listing label itself, under its own “Procedure” (the shop’s file with UL), and UL inspects the shop periodically.
The label covers the panel. UL’s guidance is that a listed panel’s certification does not extend to the loads or machines it controls.
Which components can a 508A panel use?
UL publishes a document, Requirements for Components Used in Industrial Control Panels (formerly Supplement SA of UL 508A). The version available is dated 2020-04-13 and references UL 508A 3rd edition with revisions to 2018-07-03, so confirm the current version with UL. It sorts components into three groups.
| Group | Rule | Notes |
|---|---|---|
| Listed | Any listed component can be used where UL 508A has no specific rule (section 1.1) | Must be used as intended, installed per the maker’s instructions, within marked ratings. Exception 3: equipment intended for non-industrial use, “such as consumer appliances and equipment for residential use”, shall not be used. |
| Recognized | Usable if Table 1 covers it; otherwise it “shall be investigated and described in the manufacturer’s Procedure” (2.1, 2.2) | Must stay within electrical ratings; terminals are for internal wiring only unless stated. |
| Other (neither) | “Shall be evaluated by the UL representative in accordance with the requirements in UL 508A, Appendix B or shall be described in the manufacturer’s Procedure” (3.1) | Exception: components whose electrical connections are all to a low-voltage limited-energy source (UL 508A Section 43) or a Class 2 source can be used without this (3.1 Exception). |
For programmable controllers specifically, Table 1 lists category NRAQ (listed) and NRAQ2 (recognized), evaluated to “UL 508 or UL 61010-1 and UL 61010-2-201”. Since 2026-10-28, programmable controllers can no longer hold UL 508 certification, so new product in these categories is certified to UL 61010-2-201 (Intertek). Arduino’s Opta is one small controller with this certification (certificate E531326).
Listed vs recognized: what is the difference?
UL compares them to a car and an engine (UL, Recognized Component Marks):
- A listed product (the “UL” in a circle with “LISTED”) has been investigated as a complete product for installation under the model codes.
- A recognized component (the backwards “RU” mark) has been evaluated only for factory installation inside a larger product. It comes with “conditions of acceptability”, for example “terminals are to be factory wired only” or “short circuit capability may need to be evaluated in the end-use application”.
Two consequences matter for panel builders:
- A panel assembled entirely from recognized components but never itself listed “would not be considered a UL Listed industrial control panel.”
- “A product bearing only a UL Recognized Component Mark should be treated the same as an unlisted product” when found installed in the field.
A recognized controller inside a 508A panel is fine, as long as the panel shop meets its conditions of acceptability and the Procedure covers it where Table 1 requires.
So can an unlisted Pi-based controller go in a 508A panel?
Three routes exist. Each has limits.
Route 1: Class 2 or limited-energy only. Under the 3.1 Exception, a component whose electrical connections are all to a Class 2 source or a low-voltage limited-energy circuit can be used without listing or evaluation. A Pi-based board powered from a listed Class 2 24 VDC supply, with only Class 2 sensor inputs, RS-485 and Ethernet, may fall here. It stops applying as soon as any connection is not limited energy, for example on-board relays switching 120 VAC loads or a mains-powered input. The power supply itself must be suitable (Table 1, sections 42–44 list acceptable Class 2 and limited power sources).
Route 2: Evaluation by the UL representative. Section 3.1 lets the UL representative evaluate the component against UL 508A Appendix B, or the component can be added to the shop’s Procedure. This is a per-design engineering task, it costs time and fees, and the outcome is not guaranteed. To be decided: typical cost and lead time, from a UL quote.
Route 3: Field evaluation instead of a 508A label. If the panel cannot be 508A-listed, a field evaluation body can evaluate the installed equipment on site. UL’s own programme is accredited to ISO/IEC 17020 as a field evaluation body and states it meets NFPA 790 and NFPA 791 (UL Solutions). A field label covers the specific equipment at that location, so it suits one-off installations better than repeat builds. For recognized components installed in the field, UL says a field evaluation of the end product is “the only way” for UL to verify the conditions of acceptability (UL).
If none of these fit, the realistic choice is a listed or recognized controller.
What should a panel builder check before choosing a Pi-based controller?
- Is it listed (NRAQ) or recognized (NRAQ2)? Look up the UL file number in UL Product iQ. A “UL” logo on a datasheet is not evidence.
- Is it industrial? Even a listed product is excluded if it is intended for consumer or residential use (section 1.1, Exception 3).
- What does it connect to? Map every terminal: if all are Class 2 or limited energy, Route 1 may apply. Relays or mains inputs rule it out.
- What are the conditions of acceptability? For recognized parts, read them and confirm your Procedure covers them.
- Who signs off? Ask your UL representative before the build, not at inspection. Interpretations of the component document can be requested from UL by email, as the document itself states.
- Will the AHJ accept it? The inspector has the final say on any installation.
Where does halfnine fit?
halfnine has no product yet. Whether its controller will carry a UL listing or recognition, and in which category, is not decided. To be decided: certification plan (listed NRAQ vs recognized NRAQ2), and whether the design keeps all field connections Class 2. Until a UL file number exists, panel builders should treat it as an unlisted component and use one of the routes above.
Sources
- UL: Requirements for Components Used in Industrial Control Panels (2020-04-13), accessed 2026-11-19
- UL: Recognized Component Marks, what code authorities need to know, accessed 2026-11-19
- UL Solutions, field evaluations, accessed 2026-11-19
- UL Solutions: Does a UL certified industrial control panel certification cover the equipment it controls?, accessed 2026-11-19
- Intertek Standards Update Notice: UL 508 (issued 2025-04-04, effective 2026-10-28), accessed 2026-11-19
- UL Certificate of Compliance E531326, Arduino Opta programmable controllers (2022-11-07), accessed 2026-11-19